IMAO Sliding Lock

  • English
  • Français
  • Nederlands
  • Español
  • Deutsch
  • Português

Download catalogue

Sliding Locks for Slotted Hole

The sliding lock travels in a slotted hole and locks in place with a quarter turn of the knob. If the lock is mounted to a plate or table surface, the user can lock a slotted metal bar or plate at varying distances.

Alternately, the lock can be attached to a plate or another object below a slotted bar to be locked into position anywhere along the slot travel. The knob is locked in the ON position and unlocked in the OFF position. The locking mechanism consists of a wedge that forces a shaft against the plate surface. The rated load is up to 112 lbs. The body is made from die-cast zinc with a plated chrome finish. The knob is made from either orange or black glass-fiber reinforced polyamide. The shaft/wedge is made from stainless steel, and the plunger is made from polyacetal. For the slotted steel bar, use JIS H14 grade flat bar made from SS400, S45C, SUS304, etc. The bar should be at least 30 mm wide. The slot width is 10 (+0.2/0) mm with a chamfer of about C0.3. The thickness of the bar is indicated on the grid.

For Slotted Hole - Orange For Slotted hole - black For Slotted Hole - Metal Knob
Slotted Hole-Orange Knob Slotted Hole-Black Knob Slotted Hole-Metal Knob
QCSL1003-OG QCSL1003-BK QCSL1003-S
QCSL1006-OG QCSL1006-BK QCSL1006-S

 

Riserplate

These riser plates are used with slotted hole sliding locks (QCSL series) to accommodate slotted steel bars or plates of greater thickness. The riser plate is made from SUS304 stainless steel.

QCSLSP1002 Riserplate for sliding lock for slotted hole - 2 mm QCSLSP1003 Riserplate for sliding lock for slotted hole - 3 mm

 

Sliding Locks for Square Bar

The sliding lock is mounted to a plate or table surface. A steel bar travels through the lock and can be locked in place with a quarter turn of the knob. The steel bar is locked in place when the knob is in the ON position; the steel bar can slide freely when the knob is in the OFF position. The locking mechanism consists of a wedge that forces a shaft against the surface of the steel bar. The body is made from die-cast zinc with a plated chrome finish. The knob is made from either orange or black glass-fiber reinforced polyamide. The shaft/wedge is made from stainless steel, and the flat spring is made from C519P phosphor bronze. For the steel bar, use JIS H14 grade steel made from SS400, S45C, SUS304, etc. The bar should be at least 30 mm wide.

For Square Bar - Orange Knob For Square Bar - black Knob For Square Bar - Metal Knob
Square Bar-Orange Knob Square Bar-Black Knob Square Bar-Metal Knob
QCSQ1212-OG QCSQ1212-BK QCSQ1212-S
QCSQ1616-OG QCSQ1616-BK QCSQ1616-S
QCSQ2509-OG QCSQ2509-BK QCSQ2509-S
QCSQ2512-OG QCSQ2512-BK QCSQ2512-S
QCSQ3212-OG QCSQ3212-BK QCSQ3212-S
QCSQ3216-OG QCSQ3216-BK QCSQ3216-S

Riserplate

These riser plates are used with square bar locks (QCSQ series) to provide 3 mm clearance under the steel bar. The riser plate is made from SUS304 stainless steel.

QCSQSP4003 Riserplate for sliding lock for square bar -  length 40 mmQCSQSP5003 Riserplate for sliding lock for square bar -  length 50 mm

Sliding Locks for Square Bar with Handle

QCSQ1212-L QCSQ2509-L QCSQ3212-L
QCSQ1616-L QCSQ2512-L QCSQ3216-L